1. Support
  2. Printers
  3. Lexmark Forms Printer 2591+
  4. Interactive user guide
  5. Restoring the 25XX Series Dot Matrix printers to the factory defaults
Lexmark Forms Printer 2591+

Lexmark Forms Printer 2591+

Printer features: Dot matrix

Lexmark Forms Printer 2591+ Support

Setup, installation, and configuration issues
How to set up OAuth 2.0
Restoring the 25XX Series Dot Matrix printers to the factory defaults
Configuring the 802.1X/EAP authentication on Lexmark wireless devices
What is IPSec and how to configure this data encryption feature
How to configure the network ready Lexmark 2581 or 2591 series Forms (Dot Matrix) printer in an AS/OS400 environment
How to Locate the Serial Number on a Lexmark 24xx/25xx/25xx+ Series Forms (Dot Matrix) Printer
Lexmark 25xx+ Forms (Dot Matrix) Printer ? How to Adjust the Power Saver Timeout
Lexmark 25xx+ Forms (Dot Matrix) Printer - How to Lock and Unlock the Operator Panel Buttons
How to perform network NVRAM reset
Lexmark 25xx+ Forms (Dot Matrix) Printer ? How to Properly Install the Ribbon Cartridge and Carrier Unit
How to Print a Continuous Hardware Test Page on a Lexmark Forms Printer 23XX, 24XX, and 25XX
Loading continuous paper and forms using the push tractor feed
Lexmark Forms Printer 258x or 259x Reinitializes when Connected Over the Network
How to set/change the 'Tear Off' position
Lexmark SNMP MIB and OID Values Explained (May 2019)
How to enable postscript print error information
Downloading fonts from a PCL 5 or PCL XL driver
Location of the power switch
Exporting and importing user-defined configuration settings
Capturing the Device Description (DEVD) and Output Queue (OUTQ) settings in AS/400
capturing-the-lpma-printer-discovery-tool-logs-ho4
Performing a network trace
How to use the Service Restore Tool to retrieve previously deployed licenses
Obtaining the Menu Settings page (MSP)
How to Copy/Upgrade the Printer Base Code via USB Cable
How to Copy/Upgrade the Printer Base Code via Parallel Cable
Capturing a spool or job file in Linux
Capturing a spool or job file in Macintosh OS
changing-the-geographic-region-setting-ho2599
How to change Date and Time & NTP server
Knowledge base
Setup, installation, and configuration issues

Restoring the 25XX Series Dot Matrix printers to the factory defaults

Here are steps to restore the 25XX Series Dot Matrix printers to the factory defaults.

Overview

The procedure below resets all current existing configuration settings. Perform this procedure only if strictly necessary.

Procedure

As a precautionary measure, print the printer settings page or GUID-33378c85-4d80-477a-9ee1-9820defa6365-en.dita#importing-and-exporting-ina-settings_importing-and-exporting-ina-settingsvia the printer's web page. This will provide you with reconfiguration information. Click here to access the full User's Guide for this printer.
Restoring the printer default settings
  1. Make sure the ribbon cartridge is installed and paper is loaded.
  2. Turn the printer
    Off
    .
    Use the
    Start/Stop
     button for this purpose.
  3. Open the ribbon access cover.
  4. Manually slide the printhead carriage all the way to the left until it stops.
  5. Close the ribbon access cover.
  6. Press and hold the
    Tear Off
     and
    Load/Unload
     buttons.
    Orange power LED should be visible.
  7. With the buttons held down, simultaneously turn the printer
    On
    .
    Use the
    Start/Stop
     button for this purpose.
  8. Release the buttons after observing printhead movement.
    You will see the control panel lights blink several times before the printhead moves one last time.
LEGACY ID:
HO3287

This site uses cookies for various purposes including enhancing your experience, analytics, and ads. By continuing to browse this site or by clicking "Accept and close", you agree to our use of cookies. For more information, read our Cookies page.