Fax error codes and recommendations

Overview

A fax error code
may provide the necessary information to resolve a fax issue.

Where to begin

Obtain the Transmission Log
and the Fax Call Log
, which will often display an additional fax error code
that identifies the reason for a failed fax.

See this article for information on how to view or print the fax call log.

Many of these errors are associated with poor phone line conditions
. Attenuation
(signal loss
) or excessive noise
(interference
) in the phone line are primary culprits for fax failures.

Before you contact technical support, it is recommended that you contact your phone service provider to have the phone line tested. If available, connect a standard phone to the same fax line and perform your own preliminary quality test.

Print your fax settings via Menus
> Reports
> Menu Settings Page
.

You may also view these settings from your printer's Embedded Web Server (EWS) under Reports
> Device Settings
> Analog Fax Settings
.

Further identify the fax problem.

Fax behavior observations	Then...	And...
Complete failure to send or receive faxes	See this article for general fax troubleshooting suggestions related to fax setup and phone line quality or phone line conditions...	Use your printed menus setting page and the MFP's User's Guide for additional suggestions.
No fax reception issues, but fax-send failures	See this article for preliminary diagnosis. Identify the fax error code.	Select your fax error code from the list below and follow the suggestions in the Error code suggestion chart.
No fax send issues, but fax-reception failures	See this article for preliminary diagnosis. Identify the fax error code.	Select your fax error code from the list below and follow the suggestions in the Error code suggestion chart.

How to use this document

Select the fax error code or code range below.

Perform any resolution suggestions.

If unable to find a resolution, contact Lexmark Technical Support
.

Fax error codes

Select the error code as seen on your Transmission log
or Fax Call Log
.

800 – 80E range

811 – 88A range

900

An XX
is any number within an error code range; e.g., E-713
.

Help articles referenced in the chart

Fax Setting	Article
Max Speed adjustments	Click here.
Modulation Settings	Contact Lexmark Technical Support
Rings To Answer	See User's Guide , or perform the following: Type the printer's IP address in the address field of your Web browser; e.g., http://mfp_ip_address. Click Settings > Fax Settings > Analog Fax Setup . Scroll down to Fax Receive Settings . Next to Rings to Answer , enter the number 1* . Click Submit . Continue to test until you can identify a possible conflict.
Redial Attempts	Click here.
Memory Use	Click here.
Behind a PABX	Click here.
Enable Auto Convert Color Faxes to Mono Faxes	Click here.
Resolution Adjustment	See the User's Guide , or change this setting from the control panel before initiating the fax.

View the IP address on the printer control panel in the TCP/IP section under the Networks/Ports
menu, or print a Network Setup
page to locate the IP address under the TCP/IP
heading.

*You may not have a choice to reduce this number because of extension phones
or other devices
on the same line as the printer. In this case, temporarily disconnect these devices and test again.

"Fax Error" code suggestion chart

Error code	Error code definition	Suggestions
E-000	No error occurred during fax transmission.	Not applicable

E-200	Error occurred when transmitting training.	Check line quality. Select a lower ‘ Max Speed ’ value under Fax Send settings.

E-3XX	Error occurred when receiving image data.	Check line quality. Select a lower ‘ Max Speed ’ value under Fax Receive settings. Max Speed adjustment instructions for Receive and Send are identical; however, these settings are found in two different locations.

E-4XX	Error occurred when sending image data.	Check line quality. Select a lower ‘ Max Speed ’ value under Fax Send settings.

E-5XX	Received unknown response from remote fax device.	Contact Lexmark Technical Support for suggestions if this message inhibits successful fax transmission.

6XX	Error occurred when receiving a frame.	Check line quality.

7XX	Error occurred when sending a frame.	Check line quality. Select a lower ‘ Max Speed ’ value under Fax Send settings.

800	Received EOT unexpectedly from the modem in V34 mode.	If error persists, disable .V34 modulation scheme.
802	Too many timeouts occurred during ECM reception.	Contact Lexmark Technical Support .
803	Fax was canceled by user.	Not applicable
804	Unexpectedly received disconnect command from remote end.	Check line quality. Remote device could be requesting an unsupported feature.
805	Remote fax device failed to respond to the DCS command.	Remote device could be malfunctioning.
808	T1 Timeout occurred when trying to establish a connection with remote fax device.	Contact Lexmark Technical Support for assistance.
809	T2 Timeout occurred due to loss of command/response synchronization.	Contact Lexmark Technical Support for assistance.
80A	T5 Timeout occurred when transmitting image data to remote fax device.	Check line quality. Select a lower ‘ Max Speed ’ value under Fax Send settings.
80B	Too many errors when transmitting image in ECM mode.	Check line quality. Select a lower ‘ Max Speed ’ value under Fax Send settings.
80C	Remote device failed to respond to the ‘CTC’ command.	Select a lower ‘ Max Speed ’ value under Fax Send settings.
80D	Received too many requests from remote end to repeat the previous command sent.	Check line quality. Check whether line conditions on remote end will facilitate a good connection.
80E	Functional limitation – Remote fax device does not support G3 receive capability.	Not applicable


811	Failed to detect a fax device at the remote end.	Verify MFP is answering to fax call and not a voice call. Decrease value of ‘ Rings To Answer ’ setting.
812	No more data rates available in V34 modulation scheme.	Adjust to a lower modulation scheme.
813	Timeout occurred after waiting too long to receive a good frame.	Contact Lexmark Technical Support for assistance.
814	Tried too many times at selected speed using V34 modulation scheme.	Adjust to a lower modulation scheme.
815	Fax transmission was interrupted due to power failure.	Check MFP hardware if error persists.
818	Fax transmission failed due to insufficient memory to store scanned image.	Adjust ‘ Memory Use ’ setting to allocate more memory for send jobs.
819	Fax transmission failed due to insufficient memory to store received image.	Adjust ‘ Memory Use ’ setting to allocate more memory for receive jobs.
81A	A timeout occurred during transmission of a page in ECM mode.	Select a lower ‘ Max Speed ’ value under Fax Send settings.
81B	Line too long	Rescan and transmit again.
880	Failure to transmit training successfully in V17, V29, V27ter modulation schemes.	Check line quality. Select a lower ‘ Max Speed ’ value under Fax Send settings.
881	Failure to transmit training successfully in V33, V29, V27ter modulation schemes.	Check line quality. Select a lower ‘ Max Speed ’ value under Fax Send settings.
882	Failure to transmit training successfully in V17, V29 modulation schemes.	Check line quality. Select a lower ‘ Max Speed ’ value under Fax Send settings.
883	Failure to transmit training successfully in V17, V27ter modulation schemes.	Check line quality. Select a lower ‘ Max Speed ’ value under Fax Send settings.
884	Failure to transmit training successfully in V29, V27ter modulation schemes.	Check line quality. Select a lower ‘ Max Speed ’ value under Fax Send Settings.
885	Failure to transmit training successfully in V17 modulation scheme.	Check line quality. Select a lower ‘ Max Speed ’ value under Fax Send settings.
886	Failure to transmit training successfully in V29 modulation scheme.	Check line quality. Select a lower ‘ Max Speed ’ value under Fax Send settings.
887	Failure to transmit training successfully in V27 modulation scheme.	Check line quality. Select a lower ‘ Max Speed ’ value under Fax Send settings.
888	Failure to transmit training successfully at 2400 bps in V27 modulation scheme.	Check line quality. Contact Lexmark Technical Support for assistance.
889	Failed to connect at minimum speed supported by MFP.	Incompatible connection.
88A	Failed to connect using V34 modulation scheme.	Check line quality. Adjust to a lower modulation scheme.

901	No fax tones detected from remote end.	Verify that destination number is correct. Verify whether remote fax device is enabled to receive incoming faxes.
902	No dial tone detected.	Check by enabling ‘ Behind a PABX ’ setting. Check phone line. Check MFP modem hardware.
903	Busy tone detected.	Check with remote end if successive redial attempts also fail.
904	Hardware error detected.	Check/replace MFP hardware if error persists.
905	A timeout occurred after dialing number and waiting for response.	Check with remote end if successive redial attempts also fail.
906	Fax send was cancelled by user.	Not applicable
907	Modem detected a digital line connection.	Verify MFP is connected to an analog phone line .
908	Phone line was disconnected.	Restore phone line connection.

A00	Received request for unsupported function from remote fax device.	Not applicable
A01	Received request for unsupported image width from remote fax device.	Select a smaller page width .
A02	Received request for unsupported image resolution from remote fax device.	Select a lower resolution .
A03	Received request for unsupported compression type from remote fax device.	Send – Enable Auto Convert Color Faxes to Mono Faxes . Receive – Enable Color Fax Receive .
A04	Received request for unsupported image length from remote fax device.	Select a shorter page size.
F00	Unknown error occurred.	Not applicable

LEGACY ID: SO6393